100 episodes

Bi-Weekly Podcast Focused on the Craft of Woodworking

Woodshop Life Podcast Woodshop Life Podcast

    • Education

Bi-Weekly Podcast Focused on the Craft of Woodworking

    Figured Wood Finish, Need a Drum Sander?, Lumber Drying and MORE!!

    Figured Wood Finish, Need a Drum Sander?, Lumber Drying and MORE!!

    This Episodes Questions:
    Brians Questions:
    Hey guys thanks for the best podcast You knowledge and wisdomThanks for answering my last question about what project would help build my skillsMy question now is I’m looking for a set of chisels and I don’t know what brand to get i’d save up to buy the brand that to get recommended cause I want a set that lastsThanks for your help and guidance wise ones Ashtin
    I hope you can help me:I made a 58 inch round table top out of 3/4 inch, good quality plywood. It's meant to sit on top of smaller round table (48 inches) to add additional seating for occasional use when extra guests are coming to dinner. I've done it before with good results. To make it manageable, and because it's quite heavy, I cut it in half. I use a rug pad between the smaller table and the 'topper' table to keep the 2 halves from slipping.  I fitted it and made sure it worked in the space and was stable before doing the finishing.  All good so far.My problem is: I finished one side with stain, lacquer and wax and it looks great.  Then I turned both halves over and repeated the same process on the other side.  When both sides were all finished, I noted that one of the halves had developed a slight bow, thus making the fitting together of the 2 halves a little wonky.  But, when I turned only the bowed half over, the 2 halves fit together perfectly.  YAY!   BUT - here's my problem.  With both sides lining up perfectly, and laying flat on the rug pad on top of the smaller table, the stain color is slightly different on the 2 halves.Thinking about how this happened I realized I had to open a new can of stain part way through staining the 2nd side. I must have mixed one of the cans poorly. Or maybe different batches can be slightly different?What are my options? I don't think any of these will work.Do I:1. Try to clamp the bowed half of the table topper (plywood) for awhile hoping to eliminate the bow?2. Try to refinish the halves that fit so they match?3. Come up with a latch of some sort to eliminate the bow when using the table topper?Since the lacquer is on and wax is rubbed in on both sides, I don't even think I could paint, or add a veneer.Am I stuck with a harlequin table topper? Trish O'Neill
    Guy's Questions:
    In contrast to some podcasters who seem to think we are interested in listening to them talk for the sake of talking,   you guys have the best podcast as far as communicating tips and techniques for woodworking so thank you for all your hard work.I have been been working and building things wood for many years but within the last year have dove into making more fine woodworking type of projects, with nice woods like Walnut and Cherry for example.I have been using shellac as well as 1:1:1 mixtures of BLO:Polyurethane:Turpentine and Beeswax:BLO:Turpentine for finishing so far.  Wipe on, wipe off technique... What finishes are considered best to really highlight the chatoyance/beauty nice figured woods?  It seems like the finishes I have used so far are not doing it justice that or maybe I am just too critical. Quinn
    Hey guys! Thank you so much for your hard work on the podcast. I love listening to how much fun you guys have and getting answers to questions on various woodworking topics. Great content! We are running a woodworking company, mainly doing cabinets, out of our 500 square foot garage. We have a Hammer 12" planer but would like a sander to assist with uniform door sizes. When it comes to sanders, what would you recommend? Would it be worth getting an open-ended wide belt sander (Grizzly 15" or something) for the extra horsepower and belt size, or would a drum sander be sufficient? Within the realm of drum sanders, would an open model (such as Supermax 2550) running on 110v be sufficient, or would you recommend a closed model with greater horsepower? More capacity, less power, or vice versa? Just want to hear your thoughts on width capacity, motor power, belt size, machine footprint, a

    • 56 min
    Sanding End Grain, Storing Lumber, Intimidating Projects and MORE!!

    Sanding End Grain, Storing Lumber, Intimidating Projects and MORE!!

    This Episode's Quesions:
    Brians Questions:
    I plan to build a handtool workbench in the future, maybe in a year or so, but as of right now, I do not have any workholding devices.  I have a large assembly table that does have an overhang and the top is 1.25" thick.  I have been using clamps to the top as a stop for planing and it does not work very well.  I also need a way to hold the wood for using chisels, and I haven't bought any dovetailing tools yet because of the lack of workholding devices.  Are there any good vises that don't require cutting a hole in my assembly table or makeshift ways to hold the wood until I can build a proper bench? Thanks Jeff
    When sanding end grain, say when you’ve got a panel where you’ve chamfered or rounded over the edge, which direction should you sand? I’d imagine you continue to follow the grain direction from the adjacent face grain but I’m not sure. Can you sand across the grain? Thanks for the great podcast, you guys really do have the best wood working show out there! Eric
    Guys Quesions:
    Hey GuysI am looking to set up a shop in my  unheated garage. I live in Canada so the weather is inconsistent. Very cold in the winter and very hot and humid in the summer. I am thinking of setting up a small workbench in my basement to cut joinery and do glue ups/assembly. I would keep all of my big power tools( table saw, planer etc.) in the garage. This setup would allow me to work comfortably through the year. My question is with wood movement.If I stored wood in my air conditioned basement and just took it out to the garage for a few hours at a time to plane and cut to size and then brought it back inside to cut joinery with hand tools, would the few hours spent in the humid or cold garage be enough time to warp the boards after I brought them back in?Heating the garage isn’t  a realistic option right now as I have two young children and would probably only be able to get a few hours in the shop a week. (Not worth the cost)Thanks for all of the help. This podcast has been a huge influence in helping me to get started with woodworking. Derek
    I have a small benchtop jointer that a friend gave me for free and a Dewalt 735 planer. For anything but pretty small parts, I use a sled to joint lumber in my planer. I'd like to upgrade both of these eventually. I have a big shop with plenty of power, so neither of those are an issue. My budget is generally the limiting factor. I do plan to keep using standalone machines for the convenience of maintaining settings and flexibility of workflow.  I'd like to get a big jointer first and keep using the 735 while I save up for a big, heavy 220v planer. My question is about 12 inch combo machines. I keep seeing decent 12" combo machines come up used for way less than I can find a standalone 12" jointer. I've seen a few of the Jet machines for $2k-$2500 and a friend recently got a Hammer A3 31 for $3500. Even new, combo machines seem to run way cheaper than a 12" jointer. Why? I understand the beds are shorter, but other than that, what is the disadvantage. Is it ridiculous to buy one if I have no long term need of the planer function and don't plan to use it? Parker
    Huys Quesions:
    Hey guys,Thank you for your many thoughtful responses to the questions you receive from your listeners.I  tend to get bored after I've made the same type of project several times (ie pencil boxes, pens, etc..).If I am not in a time crunch,  I like figuring out how to do something to make a project a little more challenging and interesting.I like looking at projects to give me some inspiration on how I might make a new project.  Early on in my woodworking journey I gained a lot of positive inspiration from watchin 'New Yankee Workshop'.The way Norm broke down processes in his projects was very helpful to me.However, there are some projects I've seen which are incredibly intimidating.(ie  highboys, Maloof rockers, etc...).  While I admire these types of projects,  I do

    • 55 min
    45 Deg Corners, Making Veneer, Clamping Pressure and MORE!!

    45 Deg Corners, Making Veneer, Clamping Pressure and MORE!!

    This Episodes Questions:
    Guy's Questions:
    With mothers day around the corner, I plan on knocking out a couple of small jewelry boxes. Mitered corners and book matched grain for a seamless look. 2 questions leading into this project. The first is more likely for Guy.
    In the past my boxes have been cut to 45.1 degrees to ensure a closed outside corner. My table saw is a jobsite saw and setting a precise angle is extremely difficult. I recently set up a router table and have seen guy use a 45 degree chamfer bit to cut miters this way. How close to 45 degree do these bits actually get? Is there a brand you recommend for better accuracy? How bad is the tear out?
    2nd question. In the past I used a wiping poly to finish the boxes. However VOC's are a concern for these boxes. I'd like to finish the boxes with a base coat of shellac and finish with beeswax top coat. I purchased a block of beeswax but didn't really think about how to dissolve it for quick finish. Seems like mineral spirits are the leading candidate but I'm curious if anyone has used natural oil citrus solvent for the same task (I'd likely by the version from milk paint company). Jose
    Gentlemen, thank you for all you do to support and educate the woodworking community through this podcast and other platforms.  I'm planning out a full kitchen remodel for our home and will be building the cabinets myself.  The style of cabinets will be frameless/euro style which means all the plywood will need to be edge banded.  The plywood will be pre-finished, but the doors and drawer fronts will be painted.  How would you recommend finishing the edge banding to match the door and drawer front color?  Would you do hardwood edge banding and paint it?  That seems like it would take a lot of taping which leaves room for lots of error.  Is there such a thing as custom colored edge banding for cabinets that is either iron-on or peel-and-stick?  I don't have an edge banding machine so that probably limits my options.  Thanks in advance for your help! Joel
    Hi guys,Thanks for providing some great knowledge for fellow woodworkers.My question is around drum sanders and the usefulness of them in a hobby shop. When do you use a drum sander and what type of projects are you using a drum sander on?I just purchased a 20” bandsaw and would like to start resawing veneers for projects. In the past I would buy 1/16” thick veneers from a commercial veneer shop which worked well. But I question if a drum sander is actually required/desired  for this operation. I’ve read a bunch about troubles with drum sander’s and really question if it speeds up the work.Could I just joint a fresh face, resaw. Then joint another fresh face and so on. Then glue up the panel. And either clean up the panel on the planner or ROS?In my  future I probably have a set of kitchen cabinets and various built in cabinets(which I would either buy plywood or use commercial veneer and glue my own). I normally make freestanding furniture as well. This isn’t a production shop, and I have all the normal tools for dimensioning lumber, TS, Jointer, and planer.Feel free to summarize my question, just wanted to give you guys enough context.Thanks,Jesse Beechland Furniture
    Huys Questions:
    Hi GuysHave known of & liked Guy’s YT channel for a number of years and recently came across this podcast which I’m really enjoying as I go through the back catalogue.I must be on similar wavelength to you Guy as I love (& own a lot / most of) the Incra stuff, saw your MFT style outfeed which I’m about to build a copycat of (just awaiting delivery of the aluminium extrusion) and am in the midst of milling the timber to start building your mini workbench, the plans for which I recently bought.I then happened on your YT channel the other day Huy and whilst watching the 6yo shop tour video was interested to see your boom arm. Could you tell me a bit more about it. Is it bought as is, or built up from tubing etc?Keep up the good work.T

    • 53 min
    Bandsaw Height, Darkening Cherry, Drill Press or Router? and MORE!!!

    Bandsaw Height, Darkening Cherry, Drill Press or Router? and MORE!!!

    This Episodes Questions:
    Brian's Questions:
    I'm so curious about the Laguna bandsaws that Guy used at work. Long time listeners of this podcast could easily believe that Laguna bandsaw tables are at knee height and unusable. But I have a Laguna 14/12 and the table is at 35", which seems really normal, and I'm pretty tall. All the other Laguna saws I've used or been around seem about in the same range. Is this not normal? Is Guy freakishly tall? Or an advocate of chest height bandsaw tables? Parker
    I haven't felt like my woodworking really justifies a jointer yet.  I don't generally mind using a planer sled to get flat faces and a jointer sled on the table saw to edge joint boards, but I've never tried to use those workarounds on long stock (over 4'.)  With that being said, this dinner table project that is looming ahead of me seems like it might be the moment to finally take the plunge and buy a jointer. Do you think its possible to get the table top glue-ready without a jointer? I trust my planer sled to get flat faces, but I'm wondering if you think edge jointing such long boards is possible with an extra long table saw jointer sled jig.  Any tips on milling and glue up for this table top would be very appreciated. 
    Part 2: Or maybe you guys can give me the nudge to consider this dinner table project as the moment to finally buy a jointer.  I suspect that a bench top jointer wouldn't give me much (other than efficiency) over the work arounds that I already use for milling.  Do you have any recommendations for a first jointer? I don't have major space limitations but I do like to save money, so I'm curious if you guys would send a case like mine to scour craigslist or facebook marketplace for an old delta 6".
    Thanks as always for your contributions to the woodworking community!  It can't be said too often: you guys really do make the best woodworking podcast there is!! Evan
    Guys Questions:
    Hey guys, I’m new to woodworking, really enjoying listening to the podcast!! I have a question, would you guys be able to go over what you use your 3/4, 4/4 etc lumber!? I often think that you need thick lumber for projects. I don’t have a project in mind but I bought some rough saw lumber that I plan on using for trim in the house but I bought enough to have plenty left over. Ivan
    I want to build a cherry coffee table for my house. We've got a couple of cherry pieces that I've made. I really love watching them darken and get more beautiful with age. The other pieces I've made don't really see much direct blasting sunlight so the process is subtle. The coffee table however, would get some direct morning sunlight every day (or at least for the three months of the year that we get direct sunlight in the pacific northwest). I'm worried about uneven color change and sun shadows on the top where there would be decorative objects or books or things left in one spot for a period. If I pre-darken it by leaving it in the sun for some hours or a day or two will that slow the process enough to alleviate this? If so, should I do it before or after finishing? Is there anything else I can do to help, besides not putting stuff on top of course? Parker
    Huys Questions:
    Hi Fellas, I recently purchased a horizontal crown bit ( ref: Yonico 16172 ) to apply a soft dimple to the drawer faces on my tool cabinet. I will be recessing the drawer pulls within them.The challenge that I'm facing is that the drawer faces are a little small, 5 1/2" x 3 1/4", and without being overly creative on work holding, I'm not seeing a safe way to plunge the face onto the bit in my router table, or plunge the bit into the face with a hand held router.My plan is to chuck the bit into my drill press and use that to apply the cut.  What experience, tips, or words of advice might you have in using a drill press with router bits? I have a Grizzly G7943 which only spins up to 3050 rpm.Thanks in advance, and for all that you guys do for our craft of woodworking!Justin
    I hav

    • 53 min
    Durable Kitchen Table, Hinge Wierdness, Sanding Slabs and MORE

    Durable Kitchen Table, Hinge Wierdness, Sanding Slabs and MORE

    This Episode's Questions:
    Brian's Questions:
    Gentlemen,First, I hope you all know that the sounds that pop through occasionally from your families in the background don't make a bad podcast; they make you human and THAT is part of what makes your podcast great.On the subject of families, I have 3 young sons (6, 4, 2 years old) that love "helping" with woodworking projects and learning about tools.  The family has outgrown our current dinner table, and I've been tasked with building a new one.  I'm planning a 6.5'x3.5' dinner table that doesn't need to be an showpiece heirloom dining table, but I'd love to produce something that will look nice and can handle the inevitable mayhem of a young family.   Can you recommend a wood species and some finish options that will stand up to these demands? I can feel white oak calling me here, should I answer the call?  (For context, our kitchen cabinets and floors are all darker wood tones so more dark might just blend into the background too much.)Thank you as always for your contribution to the woodworking community.  Your knowledge, experience, and unique characters make this truly the best woodworking podcast. Evan
    Hey guys! Love the podcast and appreciate all the work you put into it. My wife and I have been planning a remodel of our kitchen for a few years. I really want to build the cabinets, but also recognize that my time is pretty limited with work, and my wife doesn't want a partially completed kitchen for months. I'm currently designing the kitchen in Sketchup to a pretty high level of detail because we have some restrictions with the space that I need to ensure I take into account. The goal is to work through as much as I can in Sketchup to reduce guesswork, decisions, and time once I start  building.
    We have currently decided that I will build the cabinet boxes and face-frames since it will be easer to custom design and build for the space, and I'm researching options for outsourcing the drawer boxes and drawer/door fronts. We are planning on using rift sawn white oak with inset door and drawer fronts.
    The drawer boxes seem like a pretty easy option to outsource, but the fronts seem like they could pose some challenges that I may not be considering. Should I be worried about significant color or grain differences between the outsourced supplier, and what I can get locally to build the face-frames?Since they will be inset, do you have a recommendation on sizing when I order? For example, I'm planning on a 3/32" reveal between the face-frame and doors/drawers, should I order with 1/16" or the full 3/32" oversized so I can trim to the exact opening once the cabinets are installed in case something shifts?Thanks for the help! Jason
    Guy's Questions:
    Hi guys. Love the podcast! Wish I could find a fishing podcast as good. Life would be perfect.I made the move to a Fuji Sprayer.  I bought one with the gravity feed gun but now think I made a mistake. I think it would be easier to hold finish in the cup between coats.What is your preference and why?Thanks so much. Joe
    Hi Guys,
    I recently asked a question concerning how to glue up a frame and panel so it’s flat. I took your advice and it worked great. Thanks so much!!!I have two unrelated questions:I recently purchased expensive hinges from Horton-brasses. When I received the hinges I made a jig out of MDF so I could simply rout out the mortises for the hinges to sit in. As usual, I make the jig so they are a perfect fit for the hing. I tested the jig on a piece of scrap and the hinge fit perfectly. I then used the jig on a cabinet I made and the hinge did not fit. I tried the various hinges I purchased and only one of the hinges fit (the hinge I used to make and test the jig). After measuring the hinges, I discovered that they were all different sizes varying by about .01”. I contacted Horton-brasses and explained the problem and they told me that their acceptable tolerance is +/- .05”. With some simple math this means t

    • 58 min
    Water White Finish?, Gluing Up Square, Sagging Table Top and MORE!!

    Water White Finish?, Gluing Up Square, Sagging Table Top and MORE!!

    This Episodes Questions:
    Brian's Questions:
    Hey guys I have a kinda lengthy question, so new to woodworking and I’ve been listening to your guys podcast and really like it!! Very helpful! Question #1 is it better to have a good table saw blade over a good saw #2 is it better to have a good table saw over a good incra fence!? Back story I have a delta table saw, I got for free from a friend, I was wondering if it’s worth spending the money or save and eventually get a better saw like a powermatic table saw etc.maybe I get caught up in the details of tools and expect them to do the work for me, but I am someone that like to have the right tools for the job. Granted as new as I am it’s hard to justify $10,000 to have all the right tools, just wondering if I should focus more on making something then, on the tools! Hope it all makes sense and it’s not more of a rant!! Thank you for all the work you guys do!! Ivan
    I'm making a mantle for my living room out of rift-sawn white oak plywood. 74" long, with a miter fold design. My wife wants it to look the same way it does before applying finish, and I'm not sure how to do that or if it is even possible. I've tested with water-based poly (Minwax), but it causes it to look a bit "golden". Suggestions? Brian
    Guy's Questions:
    Hi fellas,Love the podcast and all your great advice.I recently glued up a free-standing (liquor) cabinet and was very nervous about it being square, especially since it was difficult to check for square (measuring corner to corner in the front and back) with all the various clamps on.  I ended up making the back panel (which fits into rabbets), which I knew was square, and placed it in the back (without glue) while the glue dried on the various joints (through tenons on top and bottom shelves, mid-shelves sit in stopped dados).  The idea was that if the square back panel fit correctly, it would help pull the whole cabinet into square. 
    It turned out perfectly this time (wahoo!), but am not sure if I got lucky or if this is a reliable method to come back to.  What do y'all think?  Does this method make sense?  Any other suggestions on how to check or ensure square with free-standing cabinets of a decent size (46" tall, 26" wide, 16" deep)?Thanks, Bryan
    Hi gents:  long time listener here and as I’ve said before, thanks so much for the great content you deliver.  You have discussed your spraying equipment set up in the past but I was hoping you could describe your spray BOOTH set up- obviously Brian is exempt from this question since he doesn’t apply finish.  How do you guys spray volatile finishes in the winter on your garage?  Do you have a spray booth like set up?  Do you openly spray in your garage workshops?  How do you vent potentially dangerous fumes?  Any details you can provide would be appreciated as I would like to do more spraying of shellac and I like wipe on poly both of which are challenges in winter time when you can’t work outside.Liam from Indianapolis
    Huy's Questions:
    I’ve recently found the podcast and am loving going back and learning from each episode! I’ve noticed that a ton of time has been dedicated to doling out wisdom on different types of finishing techniques and products. I’m sure the best way to learn all of this is through experience, but do you have and resources to recommend budding woodworkers as a go-to guide? With the way my brain works, learning the origins of each finish, their make-ups, and how that brings about their use cases and strengths/weaknesses would go a long way for me to internalize all of the various do’s and dont’s. Do you have a resource you go to when considering applicable finishing materials on a new project? Jeremiah
    Love the show, I appreciate you guys giving it the time it takes to make it happen. My question is about a solid Walnut table that I built for my eat in kitchen. The material was 30yr + air dried Walnut milled down to a thickness of about 15/16" for the table t

    • 56 min

Top Podcasts In Education

Learn English Podcast
Learn English Podcast
بكل ثقة
Asharq Podcasts | الشرق بودكاست
أسماء الله الحسنى
خالد السبت
بودكاست رذاذ
RathathPodcast
Think With Hessa
Hessa Alsuwaidi
Real English Conversations Podcast - Learn to Speak & Understand Real English with Confidence!
Real English Conversations: Amy Whitney & Curtis Davies - English Podcast

You Might Also Like

Shop Talk Live - Fine Woodworking
FineWoodworking.com
Wood Talk | Woodworking
The Wood Whisperer
Shannon's Lumber Industry Update
Shannon Rogers
Shop Sounds Podcast
Keith Johnson
ShopNotes Podcast
Active Interest Media
Making It With Jimmy Diresta, Bob Clagett and David Picciuto
I Like To Make Stuff