Smarter Every Season Precision Planting

Show notes for this Panorama focused episode include:
-Best practices for wifi connectivity
-Best resources including youtube videos to get started
-How to invite someone or get invited to an operation
-How to move .0 software data to Panorama
-Highlighting some handy diagnostic tools in Panorama
-When submitting a ticket, include Operation Name, turn Precision Planting Support on, the field names, and a description of the issue.

Callouts and Reminders
Speed tube high amp draw behavior, note the update on 2024.0.2RowFlow trouble shooting trees.Reminder on Sensing Y requirement for .1 software.Callout for replant instructions online.
Special guest, Marcus Lee, joins Nate and Hans as he talks about some of the highlights of Smart Scout, now available, and some awesome learning tools within the application as well as the route for support within the app.
SmartsScout available below:
Precision News: smartscout (precisionplanting.com)

General Diagnostic Steps
-       Loss of entire planter, what is the piece of information that will tell us what we should chase down first?
What are the lights doing?The light status tells us whether we are chasing communication or power.
-       Gaps or skips of coverage in field.
Dig to verify in ground what we have.Watch the GPS page to see if our GPS speed drops out while running.Watch the lift switch state in field.
2024.1.9
 
-      All .1 users should make the upgrade to 2024.1.9
Auto Load fixesMapping improvementsFlip implement
- Planters/Seeder – Flip implement only works when the plater/seeder is in the lifted state.
- Sprayers- Flip Implement will only work when the sprayer is NOT spraying.

General Notes
-      Replant Instructions are on product resources (linked below) on the steps to take when doing a replant.
Products (precisionplanting.com)
-      If someone is running liquid, and they are running a consistent rate and speed through the field, then it is fully acceptable to run in Constant and take out the time to do a pump cal.
Gen 2
-      On a 2100 series planter, when getting lift state through the Case lift switch either stay on 2020.0.1, or if updating to 2020.0.4 use a Y harness (729818). Another option to get lift state is to install a push button lift switch for lift state.
2024.1.X
-      If you have growers that are going to be running .1, and they haven’t started yet, please spend some time with them and go out and make sure that they are set up and ready to go. If the system hasn’t been set up yet, it does take some vigilance and time to make sure that things aren’t missed.
-      On a vApplyHD system, we do show shaft speed if we have a shaft speed sensor. This is different from .0 where we didn’t, this is a diagnostic tool. We don’t control to a commanded shaft speed, but it is helpful when diagnosing things to know what the shaft speed is.

System Wide Notes
Diagnostics of compressors - "My compressor won't stop running, or, my compressor wont kick on."Specialty crop and seed corn setup best practices.GPS resources, if there is a display that we don't have a document on and you figure out how to connect and where to set it up in the OEM display, please grab screenshots and let us know the steps that were taken to create a document on it.
.1
If you are on .1, please keep up to date on software updates.specialty crops and seed corn setups and crop change. Different processes in .1 than in .0 softwares.If you have a frame mounted lift switch (primarily whisker switches), you need to do the calibration. If it calibrates to 0 and 100, then put manual percentages in for 5 lowered and 95 lifted.

All systems
Resources used often - Setup Videos, Dealer Service Manual, Operation Manuals (RowFlow as an example). FieldView not connected - Check app version is up to date, hard reset of iPad, make sure fvm is green in diagnose page on gen 3, if it seems to be the ipad chord use anker as a brand.
24.0.X notes
When setting up a vApplyHD system that is either turbines removed or EMHD you must change the flow source for ALL rows. Setup - systems - liquid application - vApplyHD - continue to vApplyHD Module Assignements - flow source on far right side.
.1 notes
1.7 relieves the need for a Rate Control Module to be set up for HD's to function on an uncontrolled system.auto-loading failing is being addressed.