Matt's Basement Workshop - Audio Unknown

Welcome back to part 2 of the Bedside Table Build. We again have some wide panels that will make up the sides of the tables and they need to be milled and glued up. But rather than tackling the task by “going ALL hand plane” on the wide boards like last week I decided to mix it up a little and use both hand planes AND power tools. In other words, living up to my claim to be a “hybrid woodworker”. The task is a pretty simple one. It’s a matter of knocking down the high spots of the concave side of the board with my Jack plane until it lays flat and doesn’t rock. Then it’s over to the thickness planer to do the rest of the work. Typically it takes more time to run it through the thickness planer than to knock down those high spots, but of course the board I chose for the video was the only one of the 8 pieces that decided to be difficult and took much longer than the others. The other tasks we complete in this episode are gluing up these wide panels, including a quick touch up of the edges with my Edge Trimming Plane and then prepping the stock that will become the legs for each table. In the next episode, we’ll start working on the joinery and begin to assemble the entire project from that point forward. Help support the show - please visit our advertisers

I'm sure you've heard the trope "The cobbler's children have no shoes"? Well the same thing in the Vanderlist household can be said about furniture. Around here it feels like I'm always making something for someone else's house (or more than likely for my shop). For a long time now my wife Samantha has been asking me to build us a matching set of bedside tables. I keep asking if she wouldn't prefer something bigger and more awe striking like a new dining room table. But while that would be nice, a bedside table that actually has room to set a book AND a lamp seemed to be a higher priority. So, starting on today's episode I'm finally building those bedside tables for her. The design is simple. Straight lines, no embellishments and something with a drawer and a shelf. Samantha also asked that they be painted too. That's fine with me, I have a decent stash of Poplar that's been waiting to be used for quite a while now. I'll get us started by roughing out the stock that will be the 20"x18" tops and the 16"x16" shelfs. These dimensions are a little too big for my jointer and thickness planer, so it's a great excuse to break out the hand planes and flatten them by hand.

On today's show I'm walking you through the steps of building a very basic, utilitarian shoe organizer. And I'll admit it, I obviously didn't pay close enough attention to the warning signs when things started to go bad! It started out great. The components were milled in near record time, even with just having 30 minutes here and there during the week. I just never thought I'd be the victim of a glue-up catastrophe on this project! But even if the glue-up had gone perfect, this is the kind of project that gets tucked away in a closet or in the backroom where it gets used more than it gets seen. Which isn't a bad thing! Sometimes we don't want our projects just admired from a far, WE WANT THEM USED. This project was also just the kind of thing that let us take the new SawStop table saw out for a spin to see what we think about it. So far? It's a really nice table saw! And in the show today I even take a moment to demonstrate how easy it is to swap out the brake cartridge when switching from a regular 10" blade, to a 8" stacked dado set. The construction of the shoe organizer included a few joinery techniques; mitered corners, thru dadoes and even the use of dowels. In hindsight, it was a glue-up nightmare, but when tackled with a little strategy (apparently better than the one I used) it's possible to get the job done correctly.

Today's post is a short and sweet look at the Bypass system on the SawStop. After introducing the new saw just a couple of weeks ago, I heard from a few listeners that they were interested in hearing more about the bypass system that allows the user to "bypass the braking mechanism". The SawStop Bypass System isn't an ALL THE TIME option for users. It's a very deliberate action the user has to take to engage, and then once the motor is shut off after the cut, the saw returns to it's normal operating status. Then to re-engage it again, the procedure has to be repeated. The beauty of the Bypass System is that it can allow the user to test materials that they may be concerned will engage the braking mechanism or that they KNOW will engage it (such as aluminum or other conductive materials). For owners of any SawStop saw this information is all laid out and explained in great detail in the manual. They'll also find the procedures for conducting their own "Materials Conductivity Test" that can save you time and money discovering what works and what doesn't vs learning it the hard way. It only takes a few seconds to engage, but what it can save you in time, materials and money is huge! Next week, we're starting the construction of a Shoe Organizer for the Vanderlist Household, apparently we're the Imelda Marcos of the neighborhood and have to many shoes and no where to put them! The video will include plenty of cuts to try out the new saw, including a dado cut or two.

ENOUGH TALK ABOUT THE NEW SAW, LET'S BUILD SOMETHING WITH IT!!! I'd love to tell you it would be something über cool, ultra modern and hip...but then it wouldn't be on this show if it were. Instead, the first project on the new saw is something FOR THE NEW SAW; it's a very basic, no frills crosscut sled. [caption id="attachment_6965" align="aligncenter" width="300"] Basic Table Saw Sled[/caption] The entire sled is built from scraps and cutoffs laying around the shop, the only thing I didn't make myself was the Micro Jig ZeroPlay Guide Bars. I maybe doing this on the cheap, and can easily just toss it on the burn pile and start all over, but why worry about loose miter bar guides when I can spend the money on these reusable and adjustable manufactured ones that take all the worry our for me? (In full disclosure, when we gave away a few pairs of these over the summer, I snagged myself a set from the pile...don't worry...Micro Jig already knows) If you follow the show on either Facebook or Google+ I mentioned getting ready to build one and asked what the ones look like that you've built. A number of you responded with some really interesting ideas, both simple and WAY tweaked out. I'd love to see and hear more of your creations, please send them in and I'll put together a gallery on the website to share with everyone. Email them to mattsbasementworkshop@gmail.com. Items mentioned in today's show:Micro Jig ZeroPlay Guide Bars Help support the show - please visit our advertisers

As table saws go, I've had an opportunity over the years to use one from each of the three body types; benchtop, contractor and cabinet. While they're all tablesaws and do the same job, the specifications of each are very different. Where benchtop and contractor saws are portable in their own ways, the cabinet saw is one you probably won't be throwing in the back of a trailer or truck and hauling around from site to site. In fact, the cabinet saw is a beast of a saw and is designed with the serious hobbyist and professional woodworker in mind. I've been using my granite topped Steel City cabinet saw for a couple of years now and have been loving the features and specifications that came with it. But just recently, an opportunity came up to try another make and model of cabinet saw that has some upgraded features and specifications I didn't think we're all that important at first, but now that its here I can't wait to test them out and share the results with all of you. In today's episode I'm introducing my brand new SawStop PCS175-TGP236 1.75HP 10" Professional Cabinet Saw. In the interest of complete transparency, the opportunity to try out this model of saw and all the accessories and upgrades that accompany it was in exchange for a sponsorship and advertising deal on my website and in the show. I'm under no obligation what-so-ever to gloss over any warts I may think the saw has as I use it over time. As of the time that I'm posting this episode, I haven't had an opportunity to put the saw through it's paces yet. But that should be remedied very shortly as we get ready to start a series of projects that will have plenty of cuts being made on the saw. Then in about 6 months, I'll come back and give it as thorough a review of what I've experienced with the saw as I possibly can. I don't expect all of you to be as excited about this opportunity as I am, and I imagine some of you will express your opinions about it with me rather loudly. But I'm interested in hearing what your concerns are regarding the specifications when compared to other manufacturers and maybe even some of the myths you've heard too. So without further delay..."Hello New Saw!" Help support the show - please visit our advertisers