55 min
Tambour Doors, No Table Saw in The Shop?, Dead Flat Assembly Table & MUCH More! Woodshop Life Podcast
-
- How To
Support us on Patreon: https://www.patreon.com/woodshoplife
Sponsored by 3M Xtract
Sean
1) I’ve found some really nice walnut burl veneer that I would like to use on the tambours. I plan on veneering these on to solid walnut in the hopes of both accounting for wood movement in the veneer, and not seeing an ugly MDF substrate when opening the doors. Am I going overboard by using solid walnut for the backing substrate, or is there a way to hide the edges of the MDF as to not see them when moving the doors? And would using MDF as a substrate cause issue with the veneer moving over time? I plan on using the heat lock veneer glue to adhere the veneers to the substrate.
2) Hello Sean, Guy, and Huy. You guys always make one of the best podcasts and i love hearing your different outlooks on topics. My question today is about design and encouraging creativity. Obviously, this will be different depending on whether or not there is a client involved, but how do you decide on a direction for the design of a piece of furniture? How do you begin, with the design or the materials? Have you ever looked at a piece (or stack) of lumber and designed your project to highlight something special about it? On the other hand, have you ever designed a piece, and then had to find the perfect piece of lumber to make it with?
Thank you, Joshua from The Blackdog Studios (finding beauty in former trees)
Huy
1) So I've heard of some folks making the decision to not have a table saw in their shops. 2 main reasons cited being safety (IF ITS NOT A SAWSTOP YOU WILL DIE) and also space. Personally, I understand their position, but don't think I could do it. I simply like my saw too much. Would any of you consider it? Additionally, what operations does the table saw perform that you could not duplicate on/with another machine? I realize this is more of a thought experiment than question, but I thought I'd throw it out there.
thanks for the great show!
Mark
2) Hey all, thanks for the great show. I notice I have been getting diminished quality cuts from my full kerf glue line rip blade on my table saw. (That is- minor saw blade marks, occasional burning) in addition, I notice a touch of increased resistance as I begin to exit my rip cuts, and the blade seems to make contact again as the board moves past the blade.
To address these issues, I have adjusted the blade to about 2 thou to the left (I cut on the right of my blade generally) and adjusted my fence. I have an older , beat up Powermatic 64B contractor saw. I have noticed the plastic faces of the fence are a bit wavy (again, a few thousands, maybe about 10-15 thou variation throughout) but I have the extreme front and back of the fence perfectly aligned. My rips aren’t perfect when I cut from the left of the blade, but the resistance feels more consistent and predictable.
I am currently transitioning from hobbyist to full time and would like to solve this annoyance, as it occasionally affects my panel glue ups, and cutting board season is nearly upon us. I think for now, I will clamp on an MDF fence to see if that can help suck out the issue. If it is a fence face or alignment issue. Do you think I should maybe invest in a better fence, or should I consider replacing my glorious Powermatic saw with a SawStop Cabinet saw exclusively to spite Guy. I do have 220 in the shop now powering my heater and big Grizzly bandsaw, with amperage remaining for a 3hp cabinet. It would also be great to have a table saw with dust collection.
Side note:
Sorry for the length, y’all always ask for more details. And a replacement cabinet saw wouldn’t have to be a SawStop, but I think it may be good insurance when I can afford to hire an employee. That said, this would be an upgrade maybe 3-8 months down the line if I’m making consistent money. Longer if I can get the Powermatic figured out. I do a range of things. From small CNC projects, shelves, cutting boards, and plan to move onto selling furni
Support us on Patreon: https://www.patreon.com/woodshoplife
Sponsored by 3M Xtract
Sean
1) I’ve found some really nice walnut burl veneer that I would like to use on the tambours. I plan on veneering these on to solid walnut in the hopes of both accounting for wood movement in the veneer, and not seeing an ugly MDF substrate when opening the doors. Am I going overboard by using solid walnut for the backing substrate, or is there a way to hide the edges of the MDF as to not see them when moving the doors? And would using MDF as a substrate cause issue with the veneer moving over time? I plan on using the heat lock veneer glue to adhere the veneers to the substrate.
2) Hello Sean, Guy, and Huy. You guys always make one of the best podcasts and i love hearing your different outlooks on topics. My question today is about design and encouraging creativity. Obviously, this will be different depending on whether or not there is a client involved, but how do you decide on a direction for the design of a piece of furniture? How do you begin, with the design or the materials? Have you ever looked at a piece (or stack) of lumber and designed your project to highlight something special about it? On the other hand, have you ever designed a piece, and then had to find the perfect piece of lumber to make it with?
Thank you, Joshua from The Blackdog Studios (finding beauty in former trees)
Huy
1) So I've heard of some folks making the decision to not have a table saw in their shops. 2 main reasons cited being safety (IF ITS NOT A SAWSTOP YOU WILL DIE) and also space. Personally, I understand their position, but don't think I could do it. I simply like my saw too much. Would any of you consider it? Additionally, what operations does the table saw perform that you could not duplicate on/with another machine? I realize this is more of a thought experiment than question, but I thought I'd throw it out there.
thanks for the great show!
Mark
2) Hey all, thanks for the great show. I notice I have been getting diminished quality cuts from my full kerf glue line rip blade on my table saw. (That is- minor saw blade marks, occasional burning) in addition, I notice a touch of increased resistance as I begin to exit my rip cuts, and the blade seems to make contact again as the board moves past the blade.
To address these issues, I have adjusted the blade to about 2 thou to the left (I cut on the right of my blade generally) and adjusted my fence. I have an older , beat up Powermatic 64B contractor saw. I have noticed the plastic faces of the fence are a bit wavy (again, a few thousands, maybe about 10-15 thou variation throughout) but I have the extreme front and back of the fence perfectly aligned. My rips aren’t perfect when I cut from the left of the blade, but the resistance feels more consistent and predictable.
I am currently transitioning from hobbyist to full time and would like to solve this annoyance, as it occasionally affects my panel glue ups, and cutting board season is nearly upon us. I think for now, I will clamp on an MDF fence to see if that can help suck out the issue. If it is a fence face or alignment issue. Do you think I should maybe invest in a better fence, or should I consider replacing my glorious Powermatic saw with a SawStop Cabinet saw exclusively to spite Guy. I do have 220 in the shop now powering my heater and big Grizzly bandsaw, with amperage remaining for a 3hp cabinet. It would also be great to have a table saw with dust collection.
Side note:
Sorry for the length, y’all always ask for more details. And a replacement cabinet saw wouldn’t have to be a SawStop, but I think it may be good insurance when I can afford to hire an employee. That said, this would be an upgrade maybe 3-8 months down the line if I’m making consistent money. Longer if I can get the Powermatic figured out. I do a range of things. From small CNC projects, shelves, cutting boards, and plan to move onto selling furni
55 min