Bench Boost by Inorganic Ventures

Inorganic Ventures

0,0 (0)
CHIMIE
CHAQUE SEMAINE

Join our host and Inorganic Ventures Technical Director, Mike Booth, as he sparks insightful conversations with our panel of experts in Bench Boost, your go-to podcast for analytical chemistry enthusiasts. Together, they explore the realm of ICP, sharing tips and tricks and diving deep into all things analytical chemistry.

-3 J

Common Tips for Analyzing Low Concentrations

Send us Fan Mail This week on Bench Boost Mike shares practical tips for analyzing pharmaceutical samples at low concentrations for USP 232 elemental impurities, emphasizing that high dilution makes small contamination or carryover issues critical. He advises minimizing contamination through careful container selection (avoiding glass and using acid-leached LDPE or leached polypropylene), and outlines a typical leaching process using dilute nitric acid for seven days. He also stresses using high-purity acids (ppb/ppt grade) and method blanks to monitor impurities. For trace measurements, he recommends tightening calibration ranges with more points near the LOD/LOQ, managing washout by running blanks before/after calibration and throughout batches, using appropriate internal standards to correct drift or suppression, recalibrating about every 20 samples, and understanding signal-to-noise requirements for LOD and LOQ.

11 min
5 MAI

The J Value

Send us Fan Mail This week Mike and Ashley explain the J value used in pharmaceutical elemental impurity testing to relate typical ICP concentration units to permitted daily exposure (PDE) limits reported in micrograms per day under USP and ICH Q3D. They describe how J value accounts for both sample dilution factor and maximum daily dose, making results comparable to PDE requirements. They recommend preparing method standards at PDE limits for the relevant administration route and diluting to match the J calculation for method validation.

7 min
28 AVR.

Pharma Elemental Analysis Overview

Send us Fan Mail This week Mike & Ashley review the standardized methods for elemental impurity analysis in pharmaceuticals: ICH Q3D, USP , and USP . ICH Q3D provides guidelines for testing up to 24 elements and emphasizes risk assessment but not detailed testing calculations; USP sets elemental impurity limits; and USP addresses sample preparation and analysis and relies on ICH Q3D concepts such as “J” concentrations (to be covered next week). They explain risk assessment factors (element, route of administration, intentional addition, and screened materials) and outline element classes. They also discuss sample types (APIs, drug products, excipients) and how early screening can reduce final testing needs.

8 min
21 AVR.

Tech Support Questions 2

Send us Fan Mail The Inorganic Ventures team members answer more listener questions relevant to trace analysis. They address low mercury recovery at 2 ppb, noting mercury instability in nitric acid, adsorption to plastic, options such as preparing in HCl or stabilizing with ~1 ppm gold. They explain detection limit calculations using calibration data and blank replicates & distinguish instrument vs method detection limits, with suggestions to improve precision and sensitivity via conditions and sample introduction components. For heavy metals in blood studies, they warn of vacutainer/polypropylene contamination and recommend vessel leaching or vessel blank studies. Finally, they describe pH product certification against NIST standards, potential meter entry limitations, and temperature effects on calibration.

12 min
7 AVR.

Tech Support Questions 1

Send us Fan Mail The Inorganic Ventures team answers listener questions focused on pharmaceutical elemental impurity analysis by ICP-MS. They explain why an indium internal standard becomes unstable in high-pH matrices due to insoluble hydroxide formation and how EDTA complexation can stabilize indium when used for iodine analysis. They discuss mercury washout problems caused by volatility, adsorption to sample introduction surfaces, memory effects, and redox/speciation, and emphasize proper rinse sequencing and the roles of chloride-based rinses and specialty solutions like ICP True Rinse to prevent carryover and failed QC checks. They address poor gold recovery during heated prep due to adsorption, reduction, and volatility. Finally, they advise diluting working standards in matrices that match samples while considering element stability and compatibility in stock matrices.

12 min
31 MARS

Troubleshooting Mining Samples Common Causes of Bad Data

Send us Fan Mail This week on Bench Boost Mike, Autumn, Micah, and Josh discuss common ICP-OES/ICP-MS issues in mining analyses and how to troubleshoot them by separating sample-prep from instrument root causes. Key sample-prep problems include incomplete digestion of refractory minerals, loss of volatile analytes, spitting, and adsorption/instability during transfers. They review contamination before jumping into issues borne from instrument assays; covering the topics of matrix effects from high TDS & mitigation via dilution, internal standards, matrix matching, and more. They also note how physical effects will impact nebulization or transport efficiency. QC pitfalls with non-matrix-matched standards, internal-standard limitations, and the importance of representative CRMs are discussed before the team provides a structured troubleshooting checklist including blanks, duplicate agreement, spike recovery, dilution linearity, and multi-wavelength/isotope agreement.

24 min
24 MARS

How to Validate a New Mining Method for ICP-OES or ICP-MS

Send us Fan Mail This week on Bench Boost Mike, Autumn, and Thomas dive deep into validation procedures for ICP-OES and ICP-MS methods. They discuss the importance of planning validation parameters early, understanding sample matrices & analyte levels, and achieving complete dissolution via appropriate digestions. They review the seven key validation parameters of accuracy, precision, detection limits, linearity, selectivity, robustness, and stability. They also outline best quality control practices including analyzing blanks, CCVs, duplicates, spikes, and implementing control charts.

31 min
17 MARS

Avoiding Precipitation During Mining Sample Prep

Send us Fan Mail This week on Bench Boost the team from Inorganic Ventures discusses avoiding precipitation during sample preparation. They review mining sample challenges including high concentrations of Ca, Fe, Al, & silicates, sulfate-rich matrices forming insoluble sulfates, and rare earth elements requiring a more acidic matrix. Thomas explains how hydrolysis leads to insoluble metal hydroxides and reviews prevention strategies. Liv outlines how to use Ksp and how temperature effects compound solubility. Lastly, Autumn covers alternative ligands, such as EDTA, for higher pH stability.

15 min

Tout afficher (132)

Join our host and Inorganic Ventures Technical Director, Mike Booth, as he sparks insightful conversations with our panel of experts in Bench Boost, your go-to podcast for analytical chemistry enthusiasts. Together, they explore the realm of ICP, sharing tips and tricks and diving deep into all things analytical chemistry.

Créateur

Inorganic Ventures
Années d’activité

2023 - 2026
Épisodes

132
Classement

Tout public
Copyright

© 2026 Bench Boost by Inorganic Ventures
Site Web de l’émission

Bench Boost by Inorganic Ventures

Actualités du jour

Actualités du jour

Tous les jours