3D Printing Made Easy

Printara 3D
  • 0.0（0則評分）
  • 科技
  • 每週更新

Bite-sized 3D printing knowledge for hobbyists. New episode every week. Covering materials, printers, settings, and real-world tips.

  1. 6 天前

    Dry Spools and Recycled Filament: Full Lifecycle

    Both articles treat filament as a long game, one about keeping it dry so it stays printable, the other about where it came from and whether recycled rPLA and rPETG are worth buying. In this episode you'll learn: Most FFF filaments are hygroscopic and pull water vapor from the air, so a spool absorbs moisture on the shelf, during long prints, or in packaging that does not seal well. At melt temperature water molecules irreversibly shorten the polymer chains, producing brittle or oddly flexible prints with reduced thermal and chemical resistance. Wet filament shows up as popping and hissing in the nozzle, stringing, oozing, blobs, poor layer adhesion, and under-extrusion that can clog the nozzle. Prusament PLA Recycled is made from 100% Prusament PLA production waste, and because colors are mixed without added pigment every batch has a different shade. Filamentive uses homogeneous offcuts from partner extruders (fishing line, fencing) and reaches up to 90% recycled content. Read the full guides on our site: Drying Filament: Why and How (Dryer, Oven, Dry Box) · Recycled Filament rPLA and rPETG: Saves Money and the Planet? Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  2. 8月13日

    AMS Color Swaps and Soluble Supports Explained

    Both multi-color AMS printing and soluble supports run on the same filament-swap mechanics, so both cost you extra material and time you should budget for before you press print. In this episode you'll learn: Bambu Lab introduced the AMS in May 2022 alongside the X1 Carbon; the box has four slots, two desiccant compartments, and a humidity sensor but no heater, so it keeps filament dry rather than actively drying it. A standard 0.4 mm hotend holds roughly 50 to 100 mm3 of molten plastic, so the first few centimeters after each color change carry the old color and must be flushed to a purge tower, a purge object, or the infill. UltiMaker's data sheet lists PVA with a glass transition of 58.4°C, a melting temperature of 175.4°C, and a density of 1.23 g/cm3; PVA dissolves in plain water and is biodegradable. Prusa recommends HIPS at a 225°C to 255°C nozzle and a 100°C to 110°C bed, the same range as ABS, and HIPS dissolves in limonene or acetone. Bambu Lab's general support guide states PVA is not compatible as a support for PETG, and for the H2D warns against printing PVA and PETG at the same time from the left and right nozzles; Prusa recommends BVOH for PETG instead. Read the full guides on our site: Multi-Color Printing with AMS: When It Pays Off, When It Doesn’t · PVA vs HIPS: Soluble Supports for PLA, PETG and ABS Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  3. 8月6日

    Choosing a 3D Printer Without Overpaying or Outgrowing It

    Both articles argue that picking an FDM printer is about matching the machine to your use case, not chasing the lowest sticker price, because real cost shows up during calibration, maintenance, and expansion. In this episode you'll learn: Article 1 splits the FDM market into three buckets: budget (lowest entry barrier), flagship (time, reliability, integrated ecosystem), and DIY/kit (control, openness, unlimited modification). The budget class saves money exactly on the parts that determine hassle-free printing: automatic bed leveling, frame rigidity, extruder quality, and flow calibration. The Bambu Lab A1 and P1S are named as machines that raised the bar by integrating auto bed leveling and flow calibration by default. Article 2's month covered three weeks: choosing a first printer, maintenance and consumables (nozzles, PTFE tubes, print surfaces), and expanding into AMS and multi-material printing. Total ownership cost beyond purchase price includes filament consumption, spare nozzles, a build plate, and time spent tuning. Read the full guides on our site: 3D Printer Buying Guide: Budget vs Flagship vs DIY · 3D Printer Buying Mistakes: Reader Q&A on Hardware Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  4. 7月30日

    Fusion 360 vs Blender: Pick Your First CAD Tool

    Both articles compare the two main free modeling paths hobbyists use for 3D printing: parametric CAD in Fusion 360 for precise functional parts, and mesh sculpting in Blender for organic shapes. In this episode you'll learn: Fusion 360 offers a free personal-use license for hobbyists that includes most features needed for 3D printing, though with limits versus the paid subscription. Prusa Research offers a structured online course in 3D modeling with Autodesk Fusion aimed at complete beginners. For 3D printing, most Fusion 360 users only touch a subset of tools: sketch, extrude, fillet, and chamfer. Blender is fully free and works with a polygonal mesh of thousands to millions of triangles and quads that you shape like digital clay. Blender navigation uses middle mouse button to rotate, Shift plus middle button to pan, and scroll to zoom, with three core modes: Object, Edit, and Sculpt. Read the full guides on our site: Fusion 360 for 3D Printing: Your First Model in 30 Minutes · Blender for 3D Printing: Organic Modeling Without CAD Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  5. 7月24日

    Prusa XL vs Voron 2.4: Buy the Toolchanger or Build It

    Both articles tackle the advanced maker's fork in the road for flagship CoreXY machines: pay for a finished 5-tool toolchanger (Prusa XL) or build an open-source printer yourself (Voron 2.4). In this episode you'll learn: The Original Prusa XL is a CoreXY printer with a 360x360x360 mm build volume and a toolchanger holding up to five independent print heads, each with its own nozzle, filament, and temperature. Each XL tool is built on the Nextruder extruder and parks in a docking station at the edge of the machine; the carriage sets down one head and mechanically couples with the next in a few seconds. Because each XL tool stays permanently heated and ready, color changes swap the whole head instead of purging one shared nozzle, cutting the waste of a purge tower that can exceed the size of the part itself. The Voron 2.4 is an open-source CoreXY printer released in May 2020 by the Voron Design team founded by Maks Zolin, with public documentation, CAD, STL parts, and firmware; you build it from a bill of materials or a third-party kit. The Voron 2.4 uses a flying gantry raised by four independently driven Z motors that self-levels against the bed, plus the community StealthBurner direct-drive toolhead, and ships fully enclosed. Read the full guides on our site: Prusa XL: 5-Tool Toolchanger for Dual-Color & Multi-Material · Voron 2.4 in 2026: Is Building Your Own Printer Worth It? Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  6. 7月16日

    Under 15000 CZK in 2026: A1 mini as Your First Printer

    Both articles show that sub-15000 CZK FDM printers now ship with full auto-calibration, and the Bambu A1 mini is the cheapest gateway into color-capable, hands-off printing for a first-time buyer. In this episode you'll learn: The Bambu Lab A1 mini base version runs around 299 dollars, and the Combo with AMS lite is around 459 dollars. The A1 mini build volume is 180 x 180 x 180 mm; the full-size A1 offers a 256 mm print area. Bambu Lab introduced the A series in late 2023, targeting everyday consumers and beginners rather than prosumers. The A1 mini arrives pre-assembled and pre-leveled, and the manufacturer says it is ready for a first print in roughly 20 minutes. The enclosed Creality K1C typically sits in the 11000 to 13000 CZK range depending on the current deal. Read the full guides on our site: Bambu Lab A1 mini: Cheapest Way Into the Bambu Ecosystem · 3D Printer Under $600: Bambu A1, Creality K1C, Kobra 3 New to 3D printing? Take our free beginner course: printara3d.com/course Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  7. 7月9日

    Picking Engineering Filaments for Parts That Must Hold Up

    Both articles help you match an engineering filament (ABS, ASA, Nylon, PC) to the actual load a functional part will face, and avoid the failures that show up when you guess wrong. In this episode you'll learn: ABS and ASA share print parameters: nozzle around 240 to 260°C, heated bed at 90 to 110°C, and an enclosed chamber to suppress warping. ASA was developed to resist sunlight, while ABS in direct sun becomes brittle, yellows, and degrades at the surface, so ASA is the pick for garden, facade, or car window parts. Enclosed machines like the Bambu Lab X1C or H2S handle these materials more reliably because a stable temperature around the part is critical for ABS and PC. For load-bearing parts PLA often is not enough; PETG, ABS, or carbon fiber composites step in, and abrasive variants need a hardened nozzle. A broken microSD slot on cheap control boards is fixable with a microSD-to-full-size-SD extension adapter mounted in a printed holder, for example on an 8mm frame like the Anet A8. Read the full guides on our site: Engineering Filaments: A Decision Tree for ABS, ASA, Nylon and PC · Reader Q&A: Functional Parts and Real-World Failure Stories Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

  8. 7月2日

    Engineering Filament Tuning: Stringing and Flow Rate

    Getting clean, dimensionally accurate prints in PETG, ABS, ASA and nylon requires attacking moisture and flow rate together, not just copying PLA recipes. In this episode you'll learn: ABS and ASA print at roughly 240°C to 260°C, keeping the melt liquid longer after retraction and worsening stringing. PETG, nylon, PA-CF, ABS and ASA are hygroscopic; absorbed water flashes to steam in the nozzle and sputters material during travel moves. In PrusaSlicer the flow control is called extrusion multiplier; in Bambu Studio and OrcaSlicer it is called flow ratio. Total flow equals the firmware flow multiplier times the slicer extrusion multiplier, and M221 overrides the firmware value at runtime. Bambu Lab documentation notes PLA flows easily, ABS and nylon are denser, PETG is sticky, TPU is elastic and viscous, and composite filaments are abrasive. Read the full guides on our site: Flow Rate Calibration: Finding the Magic Number for Every Filament · Stringing in Engineering Filaments: Complete Troubleshooting Watch on YouTube: 3D Printing Made Easy playlist We 3D-print custom props and game pieces for Z-AGENCY and TerraHunt. This show is our AI bonus channel: episodes are automatically generated audio editions of the articles we publish at printara3d.com, so you can follow our topics on the go.

顯示全部 (35)

簡介

Bite-sized 3D printing knowledge for hobbyists. New episode every week. Covering materials, printers, settings, and real-world tips.

資訊

  • 創作者
    Printara 3D
  • 活躍年代
    2026年
  • 集數
    35
  • 年齡分級
    兒少適宜
  • 節目網站
    3D Printing Made Easy

你可能也會喜歡